Airaid 450-172 User Manual download pdf

Installation Instructions

For Part Numbers:

450-172 700-466 Airaid Oiled Media Filter

451-172 701-466 SynthaMax Dry Media Filter - Red

452-172 702-466 SynthaMax Dry Media Filter - Black

453-172 703-466 SynthaMax Dry Media Filter - Blue

2005-09 Ford Mustang GT

4.6L V8

1. Disconnect negative battery cable.

PLEASE READ #22 ON THE BACK PAGE!!

Push the green plastic tabs, and remove breather

hose from vehicle. (Save for later use).

2. Loosen the intake tube hose clamp on the

throttle body. Slide the red tab on the electrical

connector, and disconnect the mass air sensor.

3. With a 10mm socket, remove the bolt

holding the factory airbox to the fender and

save the bolt. It will be reused

4. Remove the complete factory intake. Use

caution to retain the factory grommets in the

inner fender.

5. Using the provided #20 torx bit, remove two

screws and the mass air sensor from the factory

airbox lid. Note the direction of the sensor for

proper re-installation later. (Save the mass air

sensor for re-installation in step #13, the factory

screws will not be re-used).

6. With a 10mm socket, remove and save

the bolt from the anti-lock brake bracket. It

will be re-installed later in step #9.

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Modular Venturi Tube (MVT) 1

4. Urethane Oval Coupler 1

5. Urethane Hump Hose 1

6. Filter Adapter 1

7. Cool Air Dam 1

8. 3/8”x12” Hose 1

9. Weather Strip 22” 1

10. ¼-20 Button Head Bolt 3

11. ¼” Flat Washer 3

12. 8-32 x 3/8” Button Head Bolt 2

13. #72 Hose Clamp 4

14. Grommet 1

15. Aluminum Spacer 1

16. 1/4” Fender Washer 1

17. Aluminum Fitting 1

18. #20 Torx Bit 1

10. Install the hump hose (#5) on the filter

adapter (#6), with two #72 hose clamps (#13).

Tighten only the clamp next to the CAD.

11. Install the supplied grommet (#14) and alu-

minum fitting (#17) into the Airaid intake tube

as shown.

12. Install the Modular Venturi Tube (MVT)

(#3) into the Airaid Intake Tube (#2) as

shown. (SEE #22 BELOW!!)

Please Note: In California, this intake is legal only on

2005 and 2006 models built after 4/30/2005.

7. Install the air filter adapter (#5) into the

Cool Air Dam (#7) as shown, using 3 but-

ton head bolts (#9) and ¼” flat washers

(#10).

8. Place the CAD into the inner fender, align

the bolt holes and re-install the bolt from step

#6.

9. Slide the Aluminum Spacer (#14)

underneath the CAD and into the hole as

shown. Secure the CAD to the inner fender

using the OEM bolt from step #3 and the

supplied 1/4” Fender Washer (#15).

1 2

Summary of Contents

Page 1 - Component Identification

Installation Instructions For Part Numbers: 450-172 700-466 Airaid Oiled Media Filter 451-172 701-466 SynthaMax Dry Media Filter - Red 452-172 702

Page 2 - Tune-Up Kit!

20. Double check your work! Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight. Doubl

Related models: 451-172 | 452-172 | 453-172 |

Comments to this Manuals

No comments

Airaid 450-172 User Manual

Browse online or download User Manual for Air equipment Airaid 450-172. Airaid 450-172 User Manual

Summary of Contents

Related models: 451-172 | 452-172 | 453-172 |

Comments to this Manuals

Related products and manuals for Air equipment Airaid 450-172