Airaid 250-242 User Manual download pdf

Installation Instructions

For Part Numbers:

250-242 720-242 Airaid Oiled Media Filter

251-242 721-242 SynthaMax Dry Media Filter - Red

252-242 722-242 SynthaMax Dry Media Filter - Black

253-242 723-242 SynthaMax Dry Media Filter - Blue

2010-11 Chevrolet Camaro

3.6L V6

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Airaid MVT 1

4. Cold Air box 1

5. Filter Adapter 1

6. Silicone Reducing Coupler 1

7. Silicone Hump Hose 1

8. Weather Strip 36” 1

9. 1/4-20 x 1/2” Button Head Bolt 3

10. 1/4-20 x 3/4” Hex Head Bolt 1

11. 1/4” Flat Washer 5

12. 1/4” Lock Washer 1

13. 1/4” Nylock Nut 1

14. 6mm x 12mm Hex Head Bolt 1

15. 6mm Flange Nut 1

16. 8-32 x 1/2” Button Head Screw 2

17. 8-32 x 5/8” Button Head Screw 1

18. #8 Kep Nut 1

19. Plastic Bumper 1

20. #16 Speed Clamp 1

21. #48 Hose Clamp 1

22 . #64 Hose Clamp 3

23. Side Bracket 1

24. Lower Bracket 1

25. 1/2” x 6” Hose 1

1. Disconnect negative battery cable.

Remove the oil fill cap and then lift up on the front of

the engine cover to remove it from the vehicle. Replace

the oil cap for now to make sure nothing falls into the

crankcase during the install.

2. Disconnect the hard plastic crankcase breather tube

from the rubber elbow. Leave the rubber elbow connect-

ed to the factory air intake tube. Next loosen the hose

clamp that secures the air intake tube to the throttle

body.

3. Using a deep 10mm socket, remove and save the two

nuts that secure the factory airbox to the fender well.

Using a 9/32” wrench or a #20 Torx bit, remove the two

screws that secure the Mass Air Flow (MAF) sensor into

the air intake tube. Without disconnecting the MAF,

carefully remove it from the tube and set it out of the

way on top of the engine.

4. Lift the complete air intake assembly straight up and

out of the vehicle.

5. Use caution not to lose the factory grommet when you

remove the air intake assembly. It will be needed if you

ever want to reinstall the factory intake assembly.

6. Squeeze the sides of the factory intake scoop and re-

move it from the factory airbox. It will be reused in step

#10.

7. Remove the two steel inserts, and grommets from the

factory airbox. Save these pieces, they will be reused in

step #8.

8. Reinstall the two steel sleeves and grommets into the

Airaid Cold Air Box (CAB) (#4). Next install the filter

adapter (#5) into the CAB as shown using three 1/4-20

button head bolts (#9), and 1/4” flat washers (#11). Re-

fer to the line drawing above for details.

9. Turn the CAB upside down and mount the lower

bracket (#24) to the bottom of the CAD using one 1/4-

20x3/4” hex bolt (#10), 1/4” flat washer (#11), and 1/4”

Nylock nut (#13) as shown. Next using one 8-32x5/8”

button head screw (#17), and one #8 Kep nut (#18), at-

tach the plastic bumper (#18) to the bracket as shown.

Filter Adapter

Breather Hose

Hose Clamp

MAF Sensor

Grommets

Plastic Bumper

Lower Bracket

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1 2

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions For Part Numbers: 250-242 720-242 Airaid Oiled Media Filter 251-242 721-242 SynthaMax Dry Media Filter - Red 252-

Page 2 - Tune-Up Kit!

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com REV.12.13.13 P/N 790-551 Aerosol Spr

Related models: 251-242 | 252-242 | 253-242 |

Comments to this Manuals

No comments

Airaid 250-242 User Manual

Browse online or download User Manual for Air equipment Airaid 250-242. Airaid 250-242 User Manual

Summary of Contents

Related models: 251-242 | 252-242 | 253-242 |

Comments to this Manuals

Related products and manuals for Air equipment Airaid 250-242