Airaid 310-132 User Manual download pdf (Page 2)

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 A[email protected]m www.airaid.com

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions

that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are

missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION

IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

13. Slide the Double Hump Hose (#6), and two #72

Hose Clamps (#28), onto straight end of the Tube. Slide

the Silicone Reducer (#7) and the #48 and #64 Clamps

on the 90 deg. bend of the Intake tube. Leave the

Clamps loose for now.

10. Replace the factory airbox grommets in the inner

fender area with the three 3/8” Well Nuts (#21).

11. Mount the Cold Air Box assembly in the inner fender

using the three 3/8” x 1 1/2” Button Head Bolts (#22)

12. A.) Install the 5/8” Barbed Fitting (#24) into the

threaded 3/8 hole in the side of the Airaid Intake Tube

(#2). B.) Transfer the air temp sensor from the factory

intake into the Airaid Intake Tube and secure it using

the #8-32 x 1/2” Button Head Bolt (#20) and #8 Fender

Washer(#19).

18. Install the Airaid Premium Filter (#1) onto the Fil-

ter Adapter.

REV.10.02.14

14. Install the Airaid Intake Tube onto the Cold Air Box

and throttle body, align and tighten all four of the

Clamps. Reconnect the air temp sensor.

15. Replace the factory breather line with the supplied

5/8” Hose (#10), and connect it to the Barbed Fitting

on the Intake Tube. Secure it using a single Speed

Clamp (#29) on each end.

16. Secure the coolant line to the fan shroud using the

two Adel Clamps (#25), 6 mm Bolts (#12), and 1/4” Flat

Washers (#11).

17. Replace the factory engine cover grommets with the

larger, Airaid Engine Cover Grommets (#23). Reinstall

the engine cover.

19. Place the Gasket (#8) onto the underside of the Air

Box Lid (#4) and peel off the protective film. Mount

the lid on the Air Box using four 1/4-20 x 1/2” Button

Head Bolts (#18), and 1/4” Flat washers (#11).

20. Double check your work!

Make sure there is no foreign material in the intake path.

Make sure all clamps, hoses, bolts, and screws are tight.

Double check the hood clearance! Reconnect the nega-

tive battery cable!

21. Pre Filter Option: Part Number 799-445

For maximum protection in the harshest environments

Airaid offers a slip on Pre Filter.

- Prolongs Cleaning Intervals

- Water Repellant

- Free Flowing Protection

FILTER IDENTIFICATION

700-462 Airaid Oiled Media 701-462 Airaid SynthaMax Dry Media - Red

702-462 Airaid SynthaMax Dry Media - Black 703-462 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we suggest

using the AIRAID Filter Tune-Up Kit!

Synthamax Air Filters do not require oil. Service air filter as needed by cleaning

with common non-petroleum all-purpose household cleaner and water. Simple

Green®, Formula 409® or equivalent works great. Apply cleaner to outside of

air filter and allow to soak. Then flush filter clean from the inside out with a gar-

den hose and repeat steps if necessary. Do not apply high pressure water or air to

clean filter. Allow filter to air dry and reinstall.

1 2

Comments to this Manuals

No comments

Airaid 310-132 User Manual Page 2

Comments to this Manuals

Related products and manuals for Air equipment Airaid 310-132