Airaid 450-245 User Manual download pdf

Installation Instructions

For Part Numbers:

450-245 700-466 Airaid Oiled Media Filter

451-245 701-466 SynthaMax Dry Media Filter - Red

452-245 702-466 SynthaMax Dry Media Filter - Black

453-245 703-466 SynthaMax Dry Media Filter - Blue

2010 Ford Mustang

4.0L V6

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. 3 1/2”to3”x2 1/2” Reducer 1

4. Urethane Hump Hose 1

5. Filter Adapter 1

6. Cool Air Dam 1

7. Weather Strip 18” 1

8. 1/4-20 Button Head Bolt 3

9. 1/4” Flat Washer 4

10. 8-32 x 3/8” Button Head Bolt 2

11. #48 Hose Clamp 1

12. #52 Hose Clamp 1

13. #72 Hose Clamp 2

14. 1/4-20 x 5/8” Hex Bolt 1

15. 1/4-20 Serrated Nut 1

16. Grommet 1

17. Bracket, Front 1

18. #20 Torx Bit 1

1. Disconnect negative battery cable.

A) Loosen the hose clamp on the throttle body.

B) Push the green tab, and disconnect the breather hose

at the factory intake tube.

C) Slide the red tab, and disconnect the Mass Air Flow

sensor wiring harness.

2. Remove the bolt that holds the factory airbox to the

driver’s side inner fender. (Save this bolt for later use in

step #9).

3. Remove the complete intake system as an assembly.

Remove the factory grommet, and steel sleeve from the

factory airbox for reuse in step #8.

4. Make sure that you retain the factory grommets in the

inner fender from the bottom of the factory airbox.

5. Using the supplied #20 torx bit, remove 2 factory

screws, and remove the MAF sensor from the factory

tube. (Save the MAF sensor for reinstallation in step

#12). Next, using a pair of side cutters, remove the met-

al band that holds the plastic breather fitting into the

factory air intake tube . Now remove the fitting from

the tube, and save it for reinstallation in step #12.

6. Using a flat blade screwdriver, pry up the center of

the three plastic trim anchors that are shown. Once the

center is up, then pry up the bottom half of the anchors

up and out of the hole and save them for reinstallation

in step #10.

7. Lift up the corner of the plastic trim from step #6 to

gain access to the bolt that secures the bracket for the

anti lock brake manifold. Remove the bolt and install the

front bracket (#17) as shown. Replace the factory bolt

and leave it just snug for now.

8. Install the filter adapter into the Cool Air Dam (#6)

using three 1/4-20 button head bolts (#8), and three 1/4”

flat washers (#9) as shown. Next install the factory

grommet and steel sleeve removed in step #3 into the

hole in the CAD.

9. Install the CAD into the vehicle aligning the locating

pins on the bottom of the CAD into the factory grom-

mets in the fender. Reinstall the factory bolt from step

#2 into the steel sleeve and grommet. Next install the

1/4-20x5/8” hex bolt (#14) thru one 1/4” flat washer

(#9) , thru the CAD, and thru the bracket securing it

with one 1/4” serrated nut (#15). Adjust for fit and then

tighten the bolt on the anti lock brake bracket.

Breather Fitting

MAF Sensor

Factory Grommet & Sleeve

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1 2

Summary of Contents

Page 1 - Component Identification

Installation Instructions For Part Numbers: 450-245 700-466 Airaid Oiled Media Filter 451-245 701-466 SynthaMax Dry Media Filter - Red 452-245 702

Page 2 - Tune-Up Kit!

10. Reposition the plastic cover and then reinstall the three plastic trim anchors removed in step #6 into their respective holes and push down the ce

Related models: 451-245 | 452-245 | 453-245 |

Comments to this Manuals

No comments

Airaid 450-245 User Manual

Browse online or download User Manual for Air equipment Airaid 450-245. Airaid 450-245 User Manual

Summary of Contents

Related models: 451-245 | 452-245 | 453-245 |

Comments to this Manuals

Related products and manuals for Air equipment Airaid 450-245