Airaid 450-238 User Manual download pdf (Page 2)

17. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and

screws are tight. Double check the hood clearance!

Reconnect the negative battery cable!

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 A[email protected]m www.airaid.com

REV.10.11.13

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions

regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are

missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-

ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is

reusable and should be cleaned periodically.

13. Install the air intake tube into the hump hose first,

and then onto the throttlebody. Adjust for fit and then

tighten all four hose clamps. Next, reinstall the factory

resonator tube into the 1 3/4” coupler and tighten the hose

clamp. Now “reseat” the resonator tube onto the bracket.

14. Install the Airaid Premium Filter (#1) onto the filter

adapter and tighten the hose clamp. Next, install the

weatherstrip (#11) onto the top of the CAD as shown

starting near the radiator and working your way towards

the left fender.

15. VERY CAREFULLY! Without cutting thr u the

connectors, cut the factory breather tube on each end just

enough to remove the factory connectors.

16. Install the two factory connectors from step #15 into

each end of the supplied 3/8”x12” breather hose (#10).

Now reattach one connector to the valve cover, and the

other end to the aluminum fitting on the intake tube.

10.A.) Thread the 1/4-20 hex bolt (#15) into the resona-

tor bracket (#22) and tighten as shown.

B.) Slide the 6mmx12mm (#16) hex bolt thr u one flat

washer (#13) and into the hole in the resonator bracket.

11. Install the bracket assembly from step #10 as shown.

This bracket and 6mm bolt will secure the power steering

reservoir and replaces the stud removed in step #9.

12.A.) Install the oval coupler onto the intake tube

using two #72 hose clamps (#17). Leave the clamps loose

for now. B.) Install the 1 3/4” coupler (#7) onto the intake

tube using two #28 hose clamps (#18) as shown. Tighten

only the clamp against the tube for now. C.) Install the

provided grommet (#19) into the intake tube and then

install the aluminum fitting (#21) into the grommet as

shown.

A. B.

18. Optional Installation Notice!

Airaid has made provisions to eliminate the factory air intake resonator if you so desire. The removal of the resonator

has no effect negative effect on the performance of this kit. Please see the addendum instruction sheet included with

these instructions for further information.

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

FILTER IDENTIFICATION

700-461 Airaid Oiled Media 701-461 Airaid SynthaMax Dry Media - Red

702-461 Airaid SynthaMax Dry Media - Black 703-461 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Fil-

ter Tune-Up Kit!

Synthamax Air Filters do not require oil.

Service air filter as needed by cleaning

with common non-petroleum all-purpose

household cleaner and water. Simple

Green®, Formula 409® or equivalent

works great. Apply cleaner to outside of

air filter and allow to soak. Then flush

filter clean from the inside out with a gar-

den hose and repeat steps if necessary.

Do not apply high pressure water or air

to clean filter. Allow filter to air dry and

reinstall.

1 2

Comments to this Manuals

No comments

Airaid 450-238 User Manual Page 2

Comments to this Manuals

Related products and manuals for Air equipment Airaid 450-238