Airaid 450-321 User Manual download pdf (Page 2)

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

13. Reconnect the Mass Air Flow sensor, which is now

located in the lower back side of the intake. Slide the

locking tab back into the connector.

14. Install the Weather Strip onto the Cool Air Box with

the contoured edge rolling away from the filter. Start at

the front of the vehicle and work your way back.

10. Install the Silicone Reducer (#6) and Hose clamps

onto the throttle body. Place the #56 clamp (#15) on the

Throttle body side of the reducer, and the #64 clamp

(#14) on to the tube side.

11. Install the Airaid Intake Tube into the couplers as

shown, and tighten all Hose Clamps. A) Reconnect the

Resonator tube to the Airaid Intake using the OEM

clamp. B) Reconnect the breather line/lines to the Alumi-

num Fittings depending on your application.

12. A) Install the Air aid Pr emium Filter onto the filter

adapter and tighten the hose clamp. B) re install the Reso-

nator tubing into the factory Stand off.

15. Double check your work!

Make sure there is no foreign material in the

intake path. Make sure all clamps, hoses, bolts,

and screws are tight. Double check the hood

clearance!

Reconnect the negative battery cable!

Optional Installation Notice!

Airaid has made it possible to eliminate the factory in-

duction roar resonator if you so desire. The removal of

the resonator from the intake has no negative effect on the

performance of this kit.

Remove the entire Resonator tube assembly and all asso-

ciated stand offs from the intake tube to the Fire wall.

A.) Install the Ur ethane cap (#7) with the 60mm Hose

Clamp (#16) onto the Airaid Intake tube.

B.) Snap the Fir ewall plug (#17) into the firewall hole.

REV.12.9.13

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions

regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are

missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-

ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter

is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-461 Airaid Oiled Media 701-461 Airaid SynthaMax Dry Media - Red

702-461 Airaid SynthaMax Dry Media - Black 703-461 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

Synthamax Air Filters do not require oil.

Service air filter as needed by cleaning

with common non-petroleum all-purpose

household cleaner and water. Simple

Green®, Formula 409® or equivalent

works great. Apply cleaner to outside of

air filter and allow to soak. Then flush

filter clean from the inside out with a gar-

den hose and repeat steps if necessary.

Do not apply high pressure water or air

to clean filter. Allow filter to air dry and

reinstall.

1 2

Comments to this Manuals

No comments

Airaid 450-321 User Manual Page 2

Comments to this Manuals

Related products and manuals for Air equipment Airaid 450-321