Airaid 883-300 User Manual download pdf

Installation Instructions

Part Number 883-300

2011-14 Polaris Ranger RZR XP

2012-14 Polaris Ranger RZR XP 4

900 E.F.I.

1. Place the range selector in Park and remove the driv-

ers seat from the vehicle. Disconnect the negative ter-

minal on the battery.

2. Starting on the Drivers side first, remove the nine T-27

head screws holding the fender in place. Remove the

fender and place it on a work bench.

3. Remove the OEM filter cover and pre filter from the

fender and set aside. They will not be reused.

4. Cut out the paper Template. Align it with the edges

of inner fender, and punch the four pilot holes. Be care-

ful with the Template as it will be re used on the pas-

senger side fender too.

5. Using a drill and a 1/8” bit, drill out the four pilot holes

in the inner fender.

7. Prepare the mating surface of the Fender Adapter

(#2) for the Foam Gasket Tape (#10) by cleaning with

a prep solvent. Apply the gasket tape along the outside

edge of the Fender Adapter as shown, avoiding the bolt

holes.

6. Using a 9/32” bit, drill out the pilot holes.

8. Attach the Fender Adapter to the outside of the factory

Fender using four 1/4-20 button head screws (#14).

Advisory Note:

Please read these installation instruc-

tions in their entirety before begin-

ning the install process. Airaid strong-

ly recommends the use of Locktite®

242 Medium strength threadlocker on

all threaded fasteners.

Tools Required For Installation:

7/16” and 1/2” Wrenches. 10mm, 7/16”, and 1/2”

Sockets.

T-27 Torx driver and 5/32” Allen Wrench. Ratchet

& Extension. 1/8”& 5/16” Drill bits.

Center punch and Mallet

Phillips and Standard Tip Screwdrivers.

Locktite ® 242 or equivalent, and a Prep– Solvent.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00

AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you.

Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing,

or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is

protected from direct exposure to water and debris; care should be taken not to drive through deep

water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY

1 2 3 4

Advisory Note: 1
Filter Service 2

Summary of Contents

Page 1 - Advisory Note:

Installation Instructions Part Number 883-300 2011-14 Polaris Ranger RZR XP 2012-14 Polaris Ranger RZR XP 4 900 E.F.I. 1. Place the range

Page 2 - Filter Service

12. Install the Hump Hose (#8) and Aluminum Intake Tube (#3) onto the Fender adapter. Loosely install two #48 Clamps (#8) onto the Hump Hose. 13. I

Page 3

24568101112111314STOCK ROLL CAGEDRIVER SIDE ASSEMBLY SHOWN937ITEM NO.AiraidPackinglistDESCRAiraidPackinglistP/NQTY.1AIRAID Premium Filter (NOT SHOWN)8

Page 4

1.003.00***CHECK SCALE BEFORE USING TEMPLATE***MARK WITH CENTERPUNCH, DRILL 1/8" PILOT HOLETHEN DRILL USING 9/32" BIT, ADJUST AS NECESSARY *

Comments to this Manuals

No comments

Airaid 883-300 User Manual

Browse online or download User Manual for Air equipment Airaid 883-300. Airaid 883-300 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Air equipment Airaid 883-300