Airaid 883-275 User Manual download pdf

Installation Instructions

For Part Number:

883-275 Scoop and Snorkel Kit

2008-14 Polaris Ranger RZR 800

800 E.F.I.

1. Many of the panels needing to be removed for this

installation are held in place with the use of nylon riv-

ets. Nylon rivets are reusable if care is taken during

their removal and installation. Using a small standard

blade screwdriver, gently pry up on the center post until

the entire rivet can be pulled freely from the panel. Riv-

et installation is the opposite.

2 Place the range selector in Park. And remove both driv-

er and passenger seats. Disconnect the negative terminal

on the battery.

3. Remove the front engine cover by rotating the two

twist locks counter clockwise and lifting out.

4. Remove the bed bolts

A.) Using a 1/2” socket, r emove the four inner bed

bolts.

B.) Using a T-25 Torx driver, remove the four outer

bed bolts.

5. Using a T-25 Torx driver and a 7/16” wrench, remove

the two outer bed bolts.

7. The bed is fastened from underneath by four Phillips

head screws in these locations. Remove these screws

on both the driver and passenger sides of the vehicle.

6. Using a T-25 Torx driver, remove the four outer bed

bolts.

8. Under side view of three bed screws to remove.

Advisory Note:

Please read these installation instruc-

tions in their entirety before begin-

ning the install process. Airaid strong-

ly recommends the use of Locktite®

242 Medium strength threadlocker on

all threaded fasteners.

B. B.

Tools Required For Installation:

7/16” and 1/2” Wrenches. 10mm, 7/16”, and

1/2” Sockets.

T-25 Torx driver and 5/32” Allen Wrench.

Ratchet & Extension. 1/8”& 5/16” Drill bits.

3” hole saw and drill.

Center punch and Mallet

Phillips and Standard Tip Screwdrivers.

Locktite ® 242 or equivalent, and a roll of tape

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951

8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear

to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts

are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air

filter element is protected from direct exposure to water and debris; care should be taken not to

drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The

air filter is reusable and should be cleaned periodically.

Page 1

1 2 3 4 5 6 7

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions For Part Number: 883-275 Scoop and Snorkel Kit 2008-14 Polaris Ranger RZR 800 800 E.F.I. 1. Many of the panels nee

Page 2

12. Remove the two rivets holding the intake shroud to the frame. Then remove the shroud and set it aside. 13. Remove the last three ri

Page 3 - Trans Mount Washer

24. Place the Air Box Gasket (#22) onto the face of the Air Box and align the bolt holes. 26. Place the Air Box assembly into the vehicle with t

Page 4

36. Position the Riser tube in the inner fender , behind the panel. Slide the Hump Hose and Clamps onto the Air Box inlet . Tighten both Hose

Page 5 - P/N 790-550 Squeeze Spray

48. The Snorkel Tube has a large mounting tab to ac-commodate many cage options. Determine the best location for attachment and drill a 5/16”

Page 6 - Component Identification

Page 6 REV.02.12.14 Component Identification 1. Airaid Premium Filter 1 2. Cold Air Box 1 3. Air Box Top 1 4. Riser Tube 1 5. Air Inle

Page 7 - ATTENTION !

6.0001.0003.00IN. HOLE SAW5/16 DRILLUSE SPRING LOADED CENTER PUNCH TO MARK HOLESSTART WITH 1/8 DRILLFOR PILOT HOLESALIGN EDGES AGAINSTRADIUS OF FENDER

Comments to this Manuals

No comments

Airaid 883-275 User Manual

Browse online or download User Manual for Air equipment Airaid 883-275. Airaid 883-275 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Air equipment Airaid 883-275