Airaid 450-172 User Manual download pdf (Page 2)

20. Double check your work!

Make sure there is no foreign material in the

intake path. Make sure all clamps, hoses,

bolts, and screws are tight. Double check the

hood clearance!

21. Reconnect the negative battery

cable!

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 A[email protected]m www.airaid.com

REV.10.24.13

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions

regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are

missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-

ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is

reusable and should be cleaned periodically.

13. Align the two slots in the tubes, and install

the factory mass air sensor removed from step

#5. Make sure the screw holes line up, then in-

stall the two supplied button head screws. (#13).

DO NOT USE THE FACTORY SCREWS!!

14. Install the oval coupler (#4) with two #72

hose clamps (#13). Tighten only the clamp

closest to the aluminum fitting. (Hint: For a

clean look, locate the hose clamp tightening

screws under the tube)!

15. A.) Install the tube into the hump hose.

B.) Now slide the oval coupler onto the

throttle body. Tighten the remaining two

hose clamps, and re-connect the mass air

sensor, from step #2.

A.

B.

16. Install the Airaid Premium Filter (#1) onto

the filter adapter, and tighten the clamp. Install

the weather strip (#9) on the top of the CAD as

shown.

17. VERY CAREFULLY ! Using a razor

blade, cut the plastic tube off both of the factory

breather hose ends as shown.

18. Install the 3/8”x12” hose (#8) onto the

factory breather ends as shown.

19. Re-connect the breather line (#8) back to

the factory locations as shown.

22. Removal of the MVT from the intake tube makes this kit “For Racing Or Offroad Use Only”, and

not legal for on-road use in the State of California. Without the MVT installed, this intake system is not

calibrated to any ECU and requires a custom tune for proper Mass Air Sensor functionality.

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not require oil.

Service air filter as needed by cleaning

with common non-petroleum all-purpose

household cleaner and water. Simple

Green®, Formula 409® or equivalent

works great. Apply cleaner to outside of

air filter and allow to soak. Then flush

filter clean from the inside out with a gar-

den hose and repeat steps if necessary.

Do not apply high pressure water or air

to clean filter. Allow filter to air dry and

reinstall.

FILTER IDENTIFICATION

700-466 Airaid Oiled Media 701-466 Airaid SynthaMax Dry Media - Red

702-466 Airaid SynthaMax Dry Media - Black 703-466 Airaid SynthaMax Dry Media - Blue

Airaid 450-172 User Manual Page 2

Comments to this Manuals

Airaid 450-172 User Manual Page 2

Comments to this Manuals

Related products and manuals for Air equipment Airaid 450-172