Airaid 510-307 User Manual download pdf (Page 2)

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions

that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are

missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION

IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

13. Install the Intake Tube and tighten all of the clamps.

Connect the crank case breather to the Barbed Fitting

and secure it using the OEM spring clamp. Insert the

resonator into the Intake Tube and tighten the clamp.

10. Route the MAF harness into the Airbox and recon-

nect the sensor inside. Seal off the access port with the

Grommet from step 9. Relocate the plastic clip on the

wire harness 1 1/4” back to take up any slack that might

allow contact with the accessory belt.

11. Place the Hump Hose (#5) and two #52 Clamps (#20)

onto the Filter Adapter and the Reducer (#6) with one #52

and one #44 Clamp (#19) on the throttle body. Leave the

clamps loose for now.

12. Install the Barbed Fitting (#21) into the Intake

Tube as shown. Remove the aluminum Plug in the

Tube if the Resonator is to be retained.

18. Place the Firewall Grommet into the bulkhead. .

NOTE: The resonator Delete option has no positive or

negative effect on performance

REV.07.29.14

15. Carefully install the Gasket (#8) onto the Air Box

Lid (#7).

14. Install the Airaid Premium Filter onto the Filter

Adapter.

20. With help from an assistant. The inlet can be re-

moved with out removing the entire bumper cover.

Simply remove all of the topside fasteners and pull back

on the cover. Have an assistant remove the two 6mm

bolts in the tube and remove.

16. Install the Air Box Lid using the 10-24 Button Head

Screws and the #10 Washers.

NOTE: Airaid recommends the use of LOCTITE®

242® Medium Strength Thread locker or equivalent on

the Air Box Lid hardware.

Double check your work !

Make sure there is no foreign material in the

intake path. Make sure all clamps, hoses,

bolts, and screws are tight. Double check the

hood clearance!

17. Install Option One: Resonator Delete. Remove the

two 6mm bolts in the diaphragm housing and pull the

sound tube out of the fire wall. Remove the entire resona-

tor as an assembly.: The Aluminum Plug will be utilized

with this option (See Step 12). It should be noted that the

Aluminum is designed to accept many 1/16 NPT N2O

foggers.

19. Install Option Two: OEM air inlet removal.

While not necessary, maximum power is achieved by

removing the OEM inlet from the vehicle.

ORIGINAL CLIP POSITION

NEW CLIP POSITION

For your Oiled media filter we suggest

using the AIRAID Filter Tune-Up Kit!

FILTER IDENTIFICATION

700-474 Airaid Oiled Media 701-474 Airaid SynthaMax Dry Media - Red

702-474 Airaid SynthaMax Dry Media - Black 703-474 Airaid SynthaMax Dry Media - Blue

Synthamax Air Filters do not require oil. Service air filter as needed by

cleaning with common non-petroleum all-purpose household cleaner and

water. Simple Green®, Formula 409® or equivalent works great. Apply

cleaner to outside of air filter and allow to soak. Then flush filter clean from

the inside out with a garden hose and repeat steps if necessary. Do not apply

high pressure water or air to clean filter. Allow filter to air dry and reinstall.

1 2

Comments to this Manuals

No comments

Airaid 510-307 User Manual Page 2

Comments to this Manuals

Related products and manuals for Air equipment Airaid 510-307